Questions tagged [s-100]
The S-100 (later the IEEE696) bus is a backplane standard introduced in 1975 supporting configurable card types.
20
questions
3
votes
2
answers
251
views
Which S-100 systems supported both hard- and soft-sectored 8-inch floppies?
In the late 1970s to early 80s incompatible system software (i.e. MicroSoft Basic and CP/M 1.4) for S100 computers could be released in 8 inch, hard and soft sector, floppy disk formats. In that era ...
- 710
5
votes
0
answers
57
views
trying to debug old 1979 Micropolis 1016-2 floppy controller issue
I have an old IMSAI PCS-80/30 S-100. It runs Micropolis MDOS 4.0.
I have Micropolis 1016-2 single drive (doesn't seem to read or write), Micropolis 1043-2 dual drive (reads sometimes when the moon is ...
- 51
21
votes
3
answers
3k
views
Anyone up for decompiling some 8080 code for Kaleidoscope?
I came across a series of blog posts about Kaleidoscope, a demo program for the Cromemco Dazzler graphics card. The series implements an emulator for the system so that it could run this code again, ...
- 20k
8
votes
2
answers
2k
views
Weird power lines for S-100, why no 5V?
In answering another question here on the S-100 bus (from my admittedly less-than-perfect recall), I wonder why the bus supplied 8 and 16 volt signals, relying on the boards to regulate this down as ...
- 4,742
7
votes
3
answers
2k
views
Why 18 expansion slots on the Altair 8800?
The Altair 8800 had a backplane with 18 connectors for S-100 cards. Why was the number 18 particularly chosen?
It is fairly common for a computer to have the number of expansion cards be a power of 2,...
- 16k
18
votes
3
answers
6k
views
Did anyone ever put half a megabyte of memory in an Altair?
The Altair 8800 typically, at least in the early years after its release in 1975, operated with no more than a few kilobytes of memory, for the excellent and sufficient reasons that memory was ...
- 61k
5
votes
1
answer
155
views
Did any S-100 cards have multi-byte peripheral registers?
This question asks about endian issues of the S-100 bus. A peripheral card that has a register larger than one byte (e.g. a 16-bit or larger word) would need to be read/written by more than one ...
- 16k
5
votes
3
answers
335
views
Did 68000 on S-100 have any problem with being big endian?
The S-100 bus was extremely versatile; originally designed for the 8080, computers using it had no trouble with the Z80 as a drop-in upgrade, and it even went to 16-bit with the 8086.
To my surprise, ...
- 61k
9
votes
1
answer
792
views
Why did the Altair use 100-pin edge connectors?
The Altair 8800 was based on what came in later years (much to the displeasure of MITS) to be known as the S-100 bus, because it had 100 lines, because MITS found 100-pin edge connectors were ...
- 61k
11
votes
1
answer
832
views
How many cards could you put on an S-100 bus?
The S-100 bus was something of an industry standard in the 1970s, for 8080 and Z80 computers built on a backplane design. It was invented with the Altair 8800, which apparently provided 16 or 18 ...
- 61k
4
votes
1
answer
239
views
How was the 8 to 16 bit transition of data lines managed for S-100
The S-100 bus had 8 data lines, logically enough since it was originally used with the 8080 and then Z80 CPUs.
However, it actually had two sets of 8 data lines. The reason why is discussed in Why ...
- 61k
11
votes
3
answers
606
views
Can anyone help provide more information regarding an operating system called I/OS by Infosoft in the early 1980's?
The title pretty much says it all. I'm looking for information about an operating system called I/OS by a company called Infosoft in the early 1980's. I think it might have been a CP/M variant and ...
- 10.2k
7
votes
1
answer
263
views
Why were the data lines of the original S-100 bus unidirectional?
The bi-directional 8-bit data bus of the Intel 8080 was split into two unidirectional 8-bit data buses. Later these two 8-bit busses would be combined to support a 16-bit data width for more advanced ...
- 16k
3
votes
2
answers
436
views
Can S-100 cards attach to the ZX machines?
S-100 was, as I understand, a very popular way to connect various computer equipment together in the past. Also, from what I understand, S-100 closely matches the same signals as the Intel 8080, as ...
- 38.9k
6
votes
4
answers
1k
views
Intel 8080 and Altair 8800. 256 I/O ports, but only 7 free RST (interrupt subroutines) — how does it work?
I have seen the video Altair 8800 - Interrupt Acknowledge Cycle and I have a few questions (I have read Wikipedia’s Intel 8080 article, the Altair 8800 Operator's manual, Charles Petzold "Code&...
- 295
7
votes
1
answer
802
views
Differences between 4k, 8k and Extended Altair BASIC?
Various histories state that there were at least three versions of Altair BASIC, 4k, 8k and Extended - plus modifications like Disk. I've found some listings of the 4k, but does anyone have a short ...
- 20k
9
votes
1
answer
703
views
Is S-100 alive?
1) Is S-100 still supported or available for serious home brew? Does anyone still actively sell new boards, cases, designing, support, etc? If not, then about what year did S-100 development stop?
2) ...
- 4,479
9
votes
3
answers
1k
views
Game cartridges on the S-100 bus?
Many Z80 computers in the seventies and early eighties used the S-100 bus, into which you could plug many kinds of expansion cards.
Would it have been possible to plug suitably designed game ...
- 61k
3
votes
0
answers
231
views
How many CP/M machines ever shipped? [closed]
How many machines for which CP/M was the primary operating system (so not counting the Commodore 128) ever shipped?
I would also be interested in knowing how many S-100 machines ever shipped. I get ...
- 61k
10
votes
2
answers
653
views
S-100 bus and device drivers
It is said that the S-100 bus provided a standard hardware format for expansion cards across many models of computers, including ones using different system software and even different CPUs.
Having ...
- 61k